Sirona XIOS XG Select Operating Instructions And Installation Download Page 59

Page: 59 / 120

Sirona Dental Systems GmbH
Gebrauchsanweisung und Installation

4 Installation

64 08 137 D3610
D3610.201.02.09.02 11.2017

4.12.3

Sensor Upgrade

IMPORTANT

The WiFi interface may not be in the charger tray for the following
steps.

Switch the WiFi interface on and wait 10 seconds until the LED
flashes.

Connect the sensor that is to receive an upgrade to the WiFi
interface.

Click on the "Wireless Monitor" symbol in the info area of the
Windows taskbar (Systray) and select the "WiFi Interface
Management" entry.

A list opens with the WiFi interfaces found in the wireless
network. It can take up to 25 seconds until all WiFi interfaces
are listed. The WiFi interfaces are named after the unit serial
number in the list.

Select the WiFi interface that is to receive an upgrade from the list.
Ensure that the WiFi interface is

not paired with the PC.

Right-click on the desired WiFi interface and select the entry "Open
Device Web Interface" in the context menu.

The "Web Server and Upgrade Utility" page is displayed.

Click the "Firmware Upgrade" tab.

Summary of Contents for XIOS XG Select

























































































































Search results

Summary of Contents for XIOS XG Select

Reviews:

Related manuals for XIOS XG Select

Brands by name

Popular brands

Sirona XIOS XG Select, Operating Instructions And Installation

Search results

Summary of Contents for XIOS XG Select

Reviews:

Related manuals for XIOS XG Select

Brands by name

Popular brands