Sirona XIOS XG Select Operating Instructions And Installation Download Page 23

Page: 23 / 120

Sirona Dental Systems GmbH
Gebrauchsanweisung und Installation

3 System description

64 08 137 D3610
D3610.201.02.09.02 11.2017

3.8

Intraoral X-ray tube assembly

The following requirements apply to the intraoral X-ray tube assembly:

Intraoral X-ray tube assembly with multipulse technology (direct current)
0.14 – 1.4 mAs at 60 – 70 kV and 8" cone

This information must be modified accordingly for other tube lengths or
single-pulse X-ray tube assemblies.

For optimal image quality we recommend using a multipulse X-ray tube
assembly with a 12"cone.

IMPORTANT

The intraoral X-ray tube assembly must be installed in accordance
with the manufacturer's instructions and requirements. Please follow
the manual for your X-ray tube assembly.

Summary of Contents for XIOS XG Select

























































































































Search results

Summary of Contents for XIOS XG Select

Reviews:

Related manuals for XIOS XG Select

Brands by name

Popular brands

Sirona XIOS XG Select, Operating Instructions And Installation

Search results

Summary of Contents for XIOS XG Select

Reviews:

Related manuals for XIOS XG Select

Brands by name

Popular brands