Sirona XIOS XG Select Operating Instructions And Installation Download Page 52

Page: 52 / 120

4 Installation

Sirona Dental Systems GmbH

Gebrauchsanweisung und Installation

64 08 137 D3610

D3610.201.02.09.02 11.2017

Hold the wireless symbol on the ON/OFF button of the WiFi
interface directly at the RFID reader.

The text "Tag read completed" appears briefly over the info
area of the Windows taskbar (Systray). The WiFi interface is
paired with the PC.

4.9.3

Remove pairing

If the WiFi interface is paired with the PC via the selection list using the
serial number (standard version), the pairing is automatically removed
again after the exposure.

If RFID technology is used for the pairing, the pairing continues with the
PC until the WiFi interface is held on the RFID reader of another PC.

The pairing is also removed where:

● the WiFi interface is switched off by pressing the On/Off button or it

switches automatically to standby following a preset period (the
period up until automatic switch-off can be adjusted).

● the paired PC is shut down

Summary of Contents for XIOS XG Select

























































































































Search results

Summary of Contents for XIOS XG Select

Reviews:

Related manuals for XIOS XG Select

Brands by name

Popular brands

Sirona XIOS XG Select, Operating Instructions And Installation

Search results

Summary of Contents for XIOS XG Select

Reviews:

Related manuals for XIOS XG Select

Brands by name

Popular brands