Sirona XIOS XG Select Operating Instructions And Installation Download Page 66

Page: 66 / 120

5 Operation

Sirona Dental Systems GmbH

Gebrauchsanweisung und Installation

64 08 137 D3610

D3610.201.02.09.02 11.2017

5.2

Determine unit status

5.2.1

LED displays on the WiFi interface

The WiFi interface is fitted with a multi-color LED. The charge state for
the storage battery and the unit status can be determined using the light
color and the flashing signals.

On/Off switch

Multi-color LED display

Light colors

When in operation the LED is green where the storage battery is fully
charged, with a red light showing where the storage battery is dead.

LED color

Storage battery charge state

green

100 - 70 %

Yellow

69 - 40 %

orange

39 - 1 %

Red

dead

When the module is switched on, the LED lights up purple until the
startup sequence has completed. The light is blue during the Firmware
update.

Summary of Contents for XIOS XG Select

























































































































Search results

Summary of Contents for XIOS XG Select

Reviews:

Related manuals for XIOS XG Select

Brands by name

Popular brands

Sirona XIOS XG Select, Operating Instructions And Installation

Search results

Summary of Contents for XIOS XG Select

Reviews:

Related manuals for XIOS XG Select

Brands by name

Popular brands