Sirona XIOS XG Select Operating Instructions And Installation Download Page 51

Page: 51 / 120

Sirona Dental Systems GmbH
Gebrauchsanweisung und Installation

4 Installation

64 08 137 D3610
D3610.201.02.09.02 11.2017

Place a check mark for

"WiFi device selection via RFID" in the

"Exposure sequence" optional group and click "Apply".

The WiFi interfaces are now paired with the PC via RFID
technology.

Execute pairing with the RFID technology

The WiFi interface must be held at the RFID reader for pairing.

Establish exposure readiness for the WiFi interface in SIDEXIS XG /
SIDEXIS 4, see also "Establish exposure readiness" [→ 70].

In the

"Select X-ray device" window, the XIOS XG WIFI ˈRFIDˈ

entry is displayed instead of the WiFi interfaces and their serial
number.

Summary of Contents for XIOS XG Select

























































































































Search results

Summary of Contents for XIOS XG Select

Reviews:

Related manuals for XIOS XG Select

Brands by name

Popular brands

Sirona XIOS XG Select, Operating Instructions And Installation

Search results

Summary of Contents for XIOS XG Select

Reviews:

Related manuals for XIOS XG Select

Brands by name

Popular brands