Sinclair ASC-18A Service Manual Download Page 86

Page: 86 / 264

DC INVERTER U-MATCH AIR CONDITIONERS INSTALLATION

Minimize the number of elbows on connection pipe.

If the connection pipe is longer than 20m, it is needed to check if the lubricating oil in the system is

enough. Add if needed.

The refrigerant charge volume inside the machine is suitable for 7m connection pipe.

To extend the

length of connection pipe, it is needed to add an appropriate quantity of refrigerant. For extension of

pipe length by every 1 meter, the refrigerant to be added is as follows. The maximum allowable

length of pipe is as follows.

If the height difference between indoor and outdoor units is over 10m, it is required to install an oil

trap every 6 meters.

When the indoor and outdoor units are on different height, please refer to Fig. 30201 for pipe layout.

Liquid pipe (i.e. fine pipe)

- - - - - -Gas pipe (i.e. coarse pipe)

Figure 3-2-1

Gas pipe

Outdoor unit

Oil elbow in

gas pipe

One oil trap shall
be arranged every
4-6

Liquid pipe

Indoor unit

Summary of Contents for ASC-18A









































































































































































































































































Search results

Summary of Contents for ASC-18A

Reviews:

Brands by name

Popular brands

Sinclair ASC-18A, Service Manual

Search results

Summary of Contents for ASC-18A

Reviews:

Brands by name

Popular brands