Sinclair ASC-18A Service Manual Download Page 126

Page: 126 / 264

DC INVERTER U-MATCH AIR CONDITION MAINTENANCE

120

◆

Radiator overheat protection

Monitor display

Mainboard indicator

Radiator overheat

protection

Blink Blink Blink

Bright Blink

Bright

If the outdoor

unit is in good

radiation?

If the air outlet and return

air inlet of the outdoor unit

is short circuited, it will

cause the radiating effect to

become poor.

If the radiator

is dirty or

blocked?

If the radiator is dirty or

blocked, it will cause the

radiating effect to become

poor.

If IPM module is

well tightened?

If IPM module is not

tightened, it will cause the

module temperature to

become too high, or even

burn the module.

If the silicate gel
on IPM module is
uniformly coated?

If the coating of silicate gel is not

uniform, it will cause poor radiation to

the module, or uneven distribution of

the temperature, or even burn the

module as the sensor cannot detect

the temperature in some area is too

high.

If the silicate gel
coated on IPM
module can meet
the requirements?

If the coating of silicate

gel is too thick, it will also

affect the radiating effect

or even burn the module.

Please check if the
sensor is failed, or
reinstall the module and
tighten it.

Record and feed back

Summary of Contents for ASC-18A









































































































































































































































































Search results

Summary of Contents for ASC-18A

Reviews:

Brands by name

Popular brands

Sinclair ASC-18A, Service Manual

Search results

Summary of Contents for ASC-18A

Reviews:

Brands by name

Popular brands