Sinclair ASC-18A Service Manual Download Page 178

Page: 178 / 264

DC INVERTER U-MATCH AIR CONDITION MAINTENANCE

161

Removal and Installation of Oil-Liquid Separator

Remarks: Before removing the oil-liquid separator, make sure that there is no refrigerant
inside the pipe system and that the power has been cut off.

1. Remove the

screws fixing the

oil-liquid

separator

●

Firstly, cut off the power.

●

Recycle the refrigerant

properly.

●

Use screwdriver to loosen

the screws fixing the oil-liquid

separator.

2. Remove the

fixing clamp of

oil-liquid

separator

●

Remove the oil-liquid

separator fixing clamp from

the support.

3. Remove the

inlet and outlet

connection pipes

of oil-liquid

separator

●

Use gas welding to heat the

inlet and outlet connection

pipes on oil-liquid separator.

Then, pull them out from the

oil-liquid separator.

●

Weld by charging nitrogen

for protection, with the

nitrogen pressure kept at

0.5±0.1kgf/c

㎡

(relative

pressure).

●

During heating, take care

to prevent the substances

around from burn due to high

temperature.

Remove the inlet and

outlet connection

pipes of oil-liquid

separator

Remove the screws

fixing the oil-liquid

separator

Summary of Contents for ASC-18A









































































































































































































































































Search results

Summary of Contents for ASC-18A

Reviews:

Brands by name

Popular brands

Sinclair ASC-18A, Service Manual

Search results

Summary of Contents for ASC-18A

Reviews:

Brands by name

Popular brands