manualshive.com logo in svg

Sinclair ASC-18A, Service Manual

Share
Download
Sinclair ASC-18A Service Manual Download Page 165

DC INVERTER U-MATCH AIR CONDITION                                       MAINTENANCE 

 

148

7,Renew the electrical source 

wire of compressor   

 

●

Install the power cable to 

the fixing screw according to 

the disassembly 

procedures. 

●

Use screwdriver to tighten 

the screws fixing the power 

cable.

。

 

8. Establish vacuum via 

Freon nozzle 

 

●

Establish vacuum inside 

the system via Freon nozzle.

9. Recharge refrigerant via 

Freon nozzle 

 

●

Recharge the refrigerant to 

the system via Freon nozzle.

●

The charge volume must 

be identical to the 

indications on nameplate. 

 

Disassembly and Assembly of 4-way valve 
Remark: Before removing the 4-way valve, make sure that there is no refrigerant inside the 
pipe system and that the power has been cut off. 

Step Illustration 

Handling 

Instruction 

 

1. Remove the solenoid valve 

 

●

Cut off the power and 

recycle the refrigerant 

properly. 

●

Remove the solenoid vale 

with spanner. 

Disconnect the 

connecting wire 

of compressor

 

Vacuum piping 

through the 

process pipe

 

Vacuum piping 

through the 

process pipe

 

Vacuum piping 

through the 

process pipe

 

Remove the 

solenoid valve

 

Summary of Contents for ASC-18A









































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands