Sinclair ASC-18A Service Manual Download Page 171

Page: 171 / 264

DC INVERTER U-MATCH AIR CONDITION MAINTENANCE

154

mark the position of each

cable correctly.

3. Remove the electric box

sub-assembly

●

Use the screwdriver to

remove the screws fixing

the electric box to middle

isolation plate, motor

support and right side plate.

4. Remove the electric box

sub-assembly

●

Move the electric box

sub-assembly upward from

the middle isolation plate.

5. Mount a new electric box

sub-assembly

●

Assemble the new electric

box sub-assembly to

correct position.

●

Use the screwdriver to fix

the electric box

sub-assembly to middle

isolation plate, motor

support and right side plate

according to disassembly

procedures.

6. Connect the power cable

of each component

●

Connect the wires of each

component to correct

position according to

disassembly procedures.

For details, please refer to

the wiring diagram.

7. Assemble the electric box

cover

●

Assemble the electric box

cover to correct position

and use screwdriver to

tighten the fixing screws.

Summary of Contents for ASC-18A









































































































































































































































































Search results

Summary of Contents for ASC-18A

Reviews:

Brands by name

Popular brands

Sinclair ASC-18A, Service Manual

Search results

Summary of Contents for ASC-18A

Reviews:

Brands by name

Popular brands