manualshive.com logo in svg

Sinclair ASC-18A, Service Manual

Share
Download
Sinclair ASC-18A Service Manual Download Page 130

DC INVERTER U-MATCH AIR CONDITION                                       MAINTENANCE 

 

124

DC B

◆

usbar Overvoltage Protection, or DC Busbar Undervoltage Protection 

 

 

E5 displayed 

on wired 

controller

 

Monitor display

 

Mainboard indicator

Driver board indicator 

DC Busbar Overvoltage 

Protection, or DC Busbar 

Undervoltage Protection 

Bright Bright Bright 

Bright blink Bright or 

Bright blink blink

Brigh blink Brigh 

Blink Dark 

Blink

 

If the input power 

voltage is within 

320V-457V?

 

If the voltage of power grid is 

too high, please immediately 

cut off the power; otherwise 

the unit will be damaged. 

Fault displayed once 

energized 

If the filter is damaged 

If the rectifier is damaged 

If the AC contactor is 

clogged 

If the filter is damaged 

If the cement resistor is 

short circuited 

If the capacitor is failed 

If the drive and module

are correctly connected 

Replace relevant elements

or reconnect the cable 

Replace the drive

Replace relevant elements 

Record and feed 

back

 

Yes 

No

No

No 

No 

No 

No

No 

No

No

Yes 

Yes 

Yes 

Yes 

Yes

Yes

Yes

Yes

Display upon startup 

of compressor 

Summary of Contents for ASC-18A









































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands