Sinclair ASC-18A Service Manual Download Page 195

Page: 195 / 264

DC INVERTER U-MATCH AIR CONDITION MAINTENANCE

178

2. Remove

the left side

plate

●

Loosen the screws

tightening the left side

plate and remove the

left side plate (As

shown, what the arrow

indicates is the left side

plate).

3. Remove

the evaporator

●

Remove the screws

fixing the evaporator.

(As shown, there are

two fixing screws at the

position pointed by the

circle and other two

screws at similar

position indicated by the

arrow)

●

Remove the

evaporator.

4. Remove

the evaporator

support

●

Loosen the tapping

screws fixing the

evaporator support and

remove the evaporator

support. (As shown,

there are two tapping

screws at the position

pointed by the circle and

other two tapping

screws at similar

position indicated by the

arrow)

Summary of Contents for ASC-18A









































































































































































































































































Search results

Summary of Contents for ASC-18A

Reviews:

Brands by name

Popular brands

Sinclair ASC-18A, Service Manual

Search results

Summary of Contents for ASC-18A

Reviews:

Brands by name

Popular brands