Sinclair ASC-18A Service Manual Download Page 63

Page: 63 / 264

DC INVERTER U-MATCH AIR CONDITIONERS INSTALLATION

）

Installation of round Supply air outlet

Figure 1-1-16

1.2 Installation of Ceiling Type

1.2.1 Before Installation

After receiving the machine, please check for any transport damage. If finding any surface or

internal damage, please immediately report to the transport company or equipment company in

writing.

After receiving the machine, please check the unit and accessories in reference to the packing list.

Ensure that the model is correct and the machine is in good condition. Please also check if the

specification and quantity of accessory parts are correct.

Determine the correct handling route and methods, thus to avoid damaging the unit or causing

possible hazard. For the sake of protection and safety, it is suggested to move the unit with the

packaging box. Even though it is not permitted to do like this under special occasions, do not

remove the packaging box, thus to avoid loosening or falling during handling.

Confirm if the installing foundation is solid. When this unit is to be installed on the metal section of

the building, make sure that the electrical insulation must comply with applicable standards.

Ensure that the place of installation is far from the area where the inflammable or explosive

substances are stored, thus to avoid possible explosion or fire due to leakage.

1.2.2 Installation Site

Such a place where cool air can be distributed throughout the room.

Such a place where condensation water is easily drained out.

Such a place that can handle the weight of indoor unit.

Such a place which has easy access for maintenance.

Such a place where is permitting easy connection with the outdoor unit.

Summary of Contents for ASC-18A









































































































































































































































































Search results

Summary of Contents for ASC-18A

Reviews:

Brands by name

Popular brands

Sinclair ASC-18A, Service Manual

Search results

Summary of Contents for ASC-18A

Reviews:

Brands by name

Popular brands