manualshive.com logo in svg

Sinclair ASC-18A, Service Manual

Share
Download
Sinclair ASC-18A Service Manual Download Page 168

DC INVERTER U-MATCH AIR CONDITION                                       MAINTENANCE 

 

151

4. Remove the motor 

power cable 

 

●

 Use hand or forceps to 

pull out the motor power 

cable from mainboard 

5. Remove the motor 

 

●

Use spanner and 

screwdriver to remove the 

bolts fixing the motor. 

●

Remove the motor from 

motor support. 

6. Install a new motor to 

motor support 

 

●

Put the new motor to 

correct position. 

●

Use spanner and 

screwdriver to fix the motor 

to motor support with bolts.

7. Connect the motor 

power cable 

 

●

 Connect the insert of 

motor power cable to the 

mainboard terminal in 

reverse to the disassembly 

procedures. 

8. Assemble the fan 

●

 Assemble the axial flow 

fan to correct position and 

fix it to the motor shaft in 

reverse to the disassembly 

procedures. 

●

Put the electric box cover 

to correct position and fix it 

onto the electric box 

according to disassembly 

procedures. 

Summary of Contents for ASC-18A









































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands