manualshive.com logo in svg

Sinclair ASC-18A, Service Manual

Share
Download
Sinclair ASC-18A Service Manual Download Page 210

DC INVERTER U-MATCH AIR CONDITION                                       MAINTENANCE 

 

193

2. Remove the 

water tray 

●

 Remove the screws 

on four corners. Then, 

pull upward to remove 

the water tray. (As 

shown, what the arrow 

indicates is the water 

tray and what the block 

indicates is the screw) 

 

Removal of Electric Box 

Remark: Cut off the power. Ensure that the power cable, signal wires and electric box are in good condition.

Step Illustration 

Handling 

Instruction 

Removal of 

Electric Box 

●

 Remove the four 

fixing screws. Then, 

pull upward to remove 

the electric box

 

 

Removal of Fan 

Remark: Cut off the power. Ensure the fan in good condition and free from deformation.

 

Step Illustration 

Handling 

Instruction

Removal of Fan 

 

●

 Use spanner to 

loosen the nuts. 

Then, pull upward to 

remove the fan. (See 

the arrow for the nut 

with gasket)

 

 
 
 

Summary of Contents for ASC-18A









































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands