Sinclair ASC-18A Service Manual Download Page 174

Page: 174 / 264

DC INVERTER U-MATCH AIR CONDITION MAINTENANCE

157

Removal and Installation of Gas-liquid Separator and Compressor

Remark: Before removing the compressor, make sure that there is no refrigerant inside the
pipe system and that the power has been cut off.

Step Illustration

Handling

Instruction

1. Remove the power

cable

●

Use screwdriver to

loosen the screws

fixing the power cable.

●

Pull out the power

cable.

Note: When removing

the power cable,

please mark the power

cable color and

corresponding

terminal, thus to avoid

error during

reinstallation.

2. Remove the nuts

fixing the gas-liquid

separator

●

Use spanner to

remove the nuts fixing

between gas-liquid

separator and

compressor support.

3. Remove the inlet

and outlet connection

pipes of gas-liquid

separator

●

Use gas welding to

heat the inlet and

outlet connection

pipes on gas-liquid

separator. Then, pull

them out from the

gas-liquid separator.

●

Weld by charging

nitrogen for protection,

with the nitrogen

pressure kept at

0.5±0.1kgf/c

㎡

(relative

pressure).

●

During heating, take

care to prevent the

substances around

from burn due to high

temperature.

Summary of Contents for ASC-18A









































































































































































































































































Search results

Summary of Contents for ASC-18A

Reviews:

Brands by name

Popular brands

Sinclair ASC-18A, Service Manual

Search results

Summary of Contents for ASC-18A

Reviews:

Brands by name

Popular brands