Sinclair ASC-18A Service Manual Download Page 123

Page: 123 / 264

DC INVERTER U-MATCH AIR CONDITION MAINTENANCE

117

◆

DC busbar overvoltage protection

E5 displayed

on wired

controller

(overcurrent

protection)

Monitor display

Mainboard indicator

Bright Bright
Bright Bright

Blink Bright

DC busbar

overvoltage

protection

If the input voltage is
within working range
(185

～

264VAC)?

If the voltage of power grid is

too high, please immediately

cut off the power and never

start the unit. Otherwise, it

might damage the unit or cause

fire!

Does this occur when
the compressor is
running?

Does this occur
repeatedly in 1 hour?

Does this occur when

the compressor

frequency is

reduced?

PFC board abnormal.

Please check if the

resistor R6, R3 and R9 in

voltage sampling circuit

on PFC board is

abnormal, or replace

PFC board.

Caused by interference.

Please check the cable

routing or determine the

source of interference,

while taking

anti-interference

measures.

Caused when the

compressor is

decelerating. If this

occurs frequently, please

check if the compressor

is abnormal.

PFC board abnormal.

Please check if the

resistor R6, R3 and R9 in

voltage sampling circuit

on PFC board is

abnormal, or replace

PFC board.

Record and feed back

Yes

Summary of Contents for ASC-18A









































































































































































































































































Search results

Summary of Contents for ASC-18A

Reviews:

Brands by name

Popular brands

Sinclair ASC-18A, Service Manual

Search results

Summary of Contents for ASC-18A

Reviews:

Brands by name

Popular brands