manualshive.com logo in svg

Sinclair ASC-18A, Service Manual

Share
Download
Sinclair ASC-18A Service Manual Download Page 194

DC INVERTER U-MATCH AIR CONDITION                                       MAINTENANCE 

 

177

3. 
Remove 
the motor 
support

 

 

●

 Loosen the 

screws fixing the 
motor support 
and remove the 
motor support 
sub-assembly. 
(As shown, what 
the arrow 
indicates is the 
motor support)

 

4. 
Remove 
the motor 

 

●

 Loosen the 

motor wiring 
plug inside the 
electric box. 
Remove the 
motor. 

 

Removal of Evaporator 

Remark: Before removal, please make sure that the power supply has been cut off. During removal, please 

take care to protect the copper tube and aluminum fin of evaporator. The copper tube shall be well sealed if 

it is to be removed for a long time. 

Step Illustration 

Handling 

Instruction 

1. Remove 

the right side 

plate 

●

 Loosen the screws 

tightening the right side 

plate and remove the 

right side plate (As 

shown, what the arrow 

indicates is the right 

side plate). 

Summary of Contents for ASC-18A









































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands