manualshive.com logo in svg

Sinclair ASC-18A, Service Manual

Share
Download
Sinclair ASC-18A Service Manual Download Page 206

DC INVERTER U-MATCH AIR CONDITION                                       MAINTENANCE 

 

189

disassembly, especially the fastening screws for fans. 

Step Illustration 

Handling 

Instruction 

1. 

Disassembly 

of front and 

back scroll 

cases

 

 

●

Press the buckle at 

the joints of front and 

back scroll cases with 

hands and pull upward 

to remove the front 

scroll case. Then 

remove the screws on 

the back scroll case. 

Lift the buckle of back 

scroll case with hands 

and remove it.(As is 

shown in the graph, 

circle represents 2 

screws on left and 

right.)  

2. 

Disassembly 

of fans 

●

Disassemble the 

fixing screws of fan 

wheel with inner 

hexagonal and remove 

the wheel. The inner 

hexagonal and its 

direction of effect are 

shown by the arrow in 

the graph. 

3. 

Disassembly 

of bearing 

fixing plates

 

●

Disassemble 4 

screws on the bearing 

fixing plates with 

screwdriver. (As 

shown in the box in the 

graph) 

Summary of Contents for ASC-18A









































































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands