Sinclair ASC-18A Service Manual Download Page 80

Page: 80 / 264

DC INVERTER U-MATCH AIR CONDITIONERS INSTALLATION

air conditioner and avoid knocking the metal parts, thus to prevent rusting in the future.

To meet the noise and vibration requirements, the outdoor unit shall be installed by using rubber

damping pad or spring damper.

The installing dimension shall comply with the installation requirements in these instructions. The

outdoor unit must be fixed at the installing position.

The installation shall be done by specialist technicians.

2.3 Caution for Installation

The outdoor unit shall be so installed that the air discharged out of the outdoor unit will not flow back

and that enough space shall be maintained around the machine for repair;

The installing position shall be in good ventilation, so that the machine can breathe and exhaust

enough air. Ensure that there is no obstruction at the inlet and outlet of the machine. If any, please

remove the obstructions blocking the air inlet and outlet.

If the outdoor unit is installed on concrete or solid ground, it shall be fixed by using M10 bolts and

nuts. And ensure that the machine is kept vertical and horizontal.

The outdoor unit must be lifted by using the designated lift hole. During lifting, take care to protect

the air conditioner and avoid knocking the metal parts, thus to prevent rusting in the future.

To meet the noise and vibration requirements, the outdoor unit shall be installed by using rubber

damping pad or spring damper.

To install the drainage pipe, please insert the drainage joint to the drainage hole on the outdoor

chassis and connect a drainage pipe on the drainage joint. (The installing height of outdoor unit

shall be at least 5cm if drainage joint is to be used).

To insert the pipe through the wall, the wall-cross tube must be installed.

The installing dimension shall comply with the installation requirements in these instructions. The

outdoor unit must be fixed at the installing position.

The installation shall be done by specialist technicians.

Summary of Contents for ASC-18A









































































































































































































































































Search results

Summary of Contents for ASC-18A

Reviews:

Brands by name

Popular brands

Sinclair ASC-18A, Service Manual

Search results

Summary of Contents for ASC-18A

Reviews:

Brands by name

Popular brands