manualshive.com logo in svg

Siemens SIRIUS 3RW44, Manual

The Siemens SIRIUS 3RW44 is a top-of-the-line motor soft starter. This high-performance device ensures a smooth and reliable start, preventing any potential motor damage. Unlock the full potential of your device by downloading the comprehensive user manual for free from manualshive.com. Get instant access to essential insights and operating instructions to make the most out of your Siemens SIRIUS 3RW44 unit.

Share
Download
background image

 

Display, controls and device interfaces 

 

5.2 Device interfaces 

3RW44 soft starters 
Manual, 03/2017, NEB535219502000/RS-AB/008 

47

 

Operator controls 

There are four keys for operating and adjusting the soft starter: 
The current function, depending on the menu item, is shown as text on the display above this 

key (e.g. select menu, change value or save settings). 
The current function, depending on the menu item, is shown as text on the display above this 

key (e.g. select menu, change value or save settings). 
The ESC key is used to quit the current menu item and to jump back to the higher-level 

menu item. 

5.2

 

Device interfaces 

5.2.1

 

Local device interface 

A local device interface on the front side of the starter is provided as standard. This interface 

can be used to connect either an optional external operating and display module, or the "Soft 

Starter ES" operating, monitoring and parameterizing software (see chapter Accessories 

(Page 277)) using a PC and a connecting cable. 

5.2.2

 

PROFIBUS/PROFINET interface (optional) 

The SIRIUS 3RW44 soft starter can be equipped with an optional PROFIBUS module (only 

available for products delivered after 04/2006) or with an optional PROFINET module (only 

available for products delivered after 06/2013). The soft starter can be connected to 

PROFIBUS/PROFINET, operated and parameterized via the interface. The "Soft Starter ES" 

operating, monitoring and parameterizing software (see chapter Accessories (Page 277)) 

can also be connected to this interface using a PC and a connecting cable. 
Simultaneous operation of a 3RW44 with a PROFIBUS/PROFINET interface is not possible 

in networks where one line conductor is grounded. 

5.3

 

External display and control module (optional) 

When de-energized, the external display and control module can be connected to the local 

device interface via a special connecting cable.  
After switching on, the SIRIUS 3RW44 soft starter automatically recognizes that the external 

display and control module has been connected. The 3RW44 display will be inverted and the 

display and control module's display will be shown normally.  
The control keys of the 3RW44 will be inactive, meaning that normal handling is only 

possible via the external display and control module.  
Refer to chapter General technical data (Page 243) for ordering data. 

Summary of Contents for SIRIUS 3RW44





































































































































































































































































































Reviews:

No comments

Related manuals for SIRIUS 3RW44

Lattice Semiconductor CrossLink Programming And Configuration Manual preview
CrossLink
Brand: Lattice Semiconductor Pages: 30
WAFER DC200 Manual preview
DC200
Brand: WAFER Pages: 15
Samson 3711 Mounting And Operating Instructions preview
3711
Brand: Samson Pages: 20
JDS Uniphase SK Series User Manual preview
SK Series
Brand: JDS Uniphase Pages: 27
Danfoss EH Series Service Manual preview
EH Series
Brand: Danfoss Pages: 20
OEG KMS Manual preview
KMS
Brand: OEG Pages: 168
Dantherm DRC1 Instructions Manual preview
DRC1
Brand: Dantherm Pages: 96
Gate Motors Q80A Quick Start Manual preview
Q80A
Brand: Gate Motors Pages: 6
Parker AC890PX Series User Mounting And Assembly Instructions preview
AC890PX Series
Brand: Parker Pages: 30
Parker Compax3M Series Installation Manual preview
Compax3M Series
Brand: Parker Pages: 52
Parker AC30V Series Manual preview
AC30V Series
Brand: Parker Pages: 337
Yealink EXP40 Quick Start Manual preview
EXP40
Brand: Yealink Pages: 8
ZKTeco C5S110 Installation And Connection Manual preview
C5S110
Brand: ZKTeco Pages: 6
POLA HP49 Handbook preview
HP49
Brand: POLA Pages: 2
Partizan PAB-FC2 Quick Start Manual preview
PAB-FC2
Brand: Partizan Pages: 7
Belden GRASS VALLEY MDX-3901 Manual To Installation And Operation preview
GRASS VALLEY MDX-3901
Brand: Belden Pages: 45
Zaiput Flow Technologies BPR-1000 Instruction Manual preview
BPR-1000
Brand: Zaiput Flow Technologies Pages: 10
Invertek Optidrive Elevator Quick Start Up Manual preview
Optidrive Elevator
Brand: Invertek Pages: 5

Brands by name

Popular brands

Load more brands