manualshive.com logo in svg

Siemens SIRIUS 3RW44, Manual

The Siemens SIRIUS 3RW44 is a top-of-the-line motor soft starter. This high-performance device ensures a smooth and reliable start, preventing any potential motor damage. Unlock the full potential of your device by downloading the comprehensive user manual for free from manualshive.com. Get instant access to essential insights and operating instructions to make the most out of your Siemens SIRIUS 3RW44 unit.

Share
Download
background image

PROFIBUS DP communication module 

 

9.9 Diagnosis with STEP 7 

 

3RW44 soft starters 

174

 

Manual, 03/2017, NEB535219502000/RS-AB/008 

9.9.4

 

Station status 1 to 3 

Definition 

The station status 1 to 3 provides an overview of the status of a DP slave. 

Table 9- 10  Structure of station status 1 (byte 0) 

Bit 

Meaning 

Cause/remedy 

0 

1: The DP master cannot address the DP slave. 

•

 

Correct station address set on the DP slave? 

•

 

Is the bus connector in place? 

•

 

Voltage at the DP slave? 

•

 

Is the RS 485 repeater set correctly? 

•

 

Reset triggered on the DP Slave? 

1 

1: The DP slave is not yet ready for the data 

transfer. 

•

 

Wait, the DP slave is currently starting up. 

2 

1: The configuration data transferred from the DP 

master to the DP slave does not match the DP slave 

configuration. 

•

 

Verify the station type or DP slave configuration in the 

configuration software. 

3 

1: External diagnostics information is pending 

(group diagnostics indication) 

•

 

Evaluate the ID-specific and/or channel-specific 

diagnostic information, and the module status. As soon 

as all errors are remedied the bit 3 is reset. The bit will 

be set again when there is a new diagnostics message 

in the bytes of the aforementioned diagnostics. 

4 

1: The required function is not supported by the DP 

slave (for example, changing the station address by 

means of software). 

•

 

Check the configuration. 

5 

1: The DP master cannot interpret the response of 

the DP slave. 

•

 

Check the bus configuration. 

6 

1: The DP slave type does not match the software 

configuration. 

•

 

Has the correct station type been entered in the 

configuration software? 

7 

1: The DP slave has been parameterized by another 

DP master (not by the DP master that has access to 

the DP slave at the moment). 

•

 

The bit is always 1, for example, if you access the DP 

slave with the PG or another DP master.  

The "Master PROFIBUS address" diagnostic byte 

contains the station address of the DP master that 

assigned parameters to the DP slave. 

Summary of Contents for SIRIUS 3RW44





































































































































































































































































































Reviews:

No comments

Related manuals for SIRIUS 3RW44

Canarm MC Series Installation Manual preview
MC Series
Brand: Canarm Pages: 3
Gardena 4030 Operating Instructions Manual preview
4030
Brand: Gardena Pages: 17
SAFI DN15 Manual preview
DN15
Brand: SAFI Pages: 18
Badger Meter Orion Series Quick Start Manual preview
Orion Series
Brand: Badger Meter Pages: 2
Badger Meter MDS 2000 Installation And Software Manual preview
MDS 2000
Brand: Badger Meter Pages: 48
Badger Meter BadgerTouch HREBT Manual preview
BadgerTouch HREBT
Brand: Badger Meter Pages: 12
Badger Meter CB-30 User Manual preview
CB-30
Brand: Badger Meter Pages: 16
Hach sc200 Software Update preview
sc200
Brand: Hach Pages: 2
Hach ORBISPHERE 410 Quick Operator'S Manual preview
ORBISPHERE 410
Brand: Hach Pages: 12
Hach AS950 AWRS Basic Operations preview
AS950 AWRS
Brand: Hach Pages: 472
Hach sc1000 User Manual preview
sc1000
Brand: Hach Pages: 64
V2 ELETTRONICA CL1 Quick Start Manual preview
CL1
Brand: V2 ELETTRONICA Pages: 6
Hach SC4500 Basic User Manual preview
SC4500
Brand: Hach Pages: 210
Xilinx Virtex-6 FPGA Hardware Setup Manual preview
Virtex-6 FPGA
Brand: Xilinx Pages: 2
Danfoss ChangeOver6 Operating Manual preview
ChangeOver6
Brand: Danfoss Pages: 2
Elfa 75-576-22 Manual preview
75-576-22
Brand: Elfa Pages: 22
Tripp Lite SRCOOLNET2LX Installation And Quick Start Manual preview
SRCOOLNET2LX
Brand: Tripp Lite Pages: 40
DS Produkte AN-A326 Instructions preview
AN-A326
Brand: DS Produkte Pages: 4

Brands by name

Popular brands

Load more brands