Siemens SIRIUS 3RW44 Manual Download Page 185

Page: 185 / 292

PROFIBUS DP communication module

9.11 Identification number (ID No.), error codes

3RW44 soft starters
Manual, 03/2017, NEB535219502000/RS-AB/008

185

Error codes

The following error codes are generated by the soft starter:

Table 9- 15 Error codes

Error codes
Byte

Error message

Cause

High

Low

No error

Communication interface
80

Negative acknowledgement for "Read

data set"

•

Data set write-only

Negative acknowledgement for "Write

data set"

•

Data set read-only

Protocol error

•

Layer 2 (fieldbus)

•

Device interface

•

Incorrect coordination

This function is not supported

•

DPV1 service does not support

Read/write data set

Access to technology
80

Unknown data set number

•

Data set number not known in the

soft starter

Incorrect data set length when writing

•

Data set length and specified data

set length different

Incorrect slot number

•

Slot not 1 or 4

Communication partner declined data

acceptance!

•

Incorrect operating mode (automatic,

manual bus, manual mode local)

•

Data set is read-only

•

Parameters cannot be changed in

ON state

80H

Invalid parameter

•

Invalid parameter value

Device resources
80

Temporary lack of resources in the

device!

•

No free receive buffer

•

The data set is currently being

updated

•

The data set request is currently

active on another interface.

Summary of Contents for SIRIUS 3RW44





































































































































































































































































































Search results

Summary of Contents for SIRIUS 3RW44

Reviews:

Related manuals for SIRIUS 3RW44

Brands by name

Popular brands

Siemens SIRIUS 3RW44, Manual

Search results

Summary of Contents for SIRIUS 3RW44

Reviews:

Related manuals for SIRIUS 3RW44

Brands by name

Popular brands