Siemens SIRIUS 3RW44 Manual Download Page 146

Page: 146 / 292

Diagnostics and messages

8.1 Diagnostics and messages

3RW44 soft starters

146

Manual, 03/2017, NEB535219502000/RS-AB/008

Message

①

②

③

Cause/solution

No external starting parameters

received (devices with product

version ≥ *E06*)

Occurs only during operation with PROFIBUS DP. Incorrect or

impermissible parameter values have been sent by the PLC.

Remedy: The Soft Starter ES software can be used to read the

incorrect parameter and to change it to a permissible value.

PIO error (devices with product

version ≥ *E06*)

x PIO error (faulty process image of the outputs) appears

•

If Motor CW and Motor CCW have been selected simultaneously

(cause 1) or

•

If Parameter set 4 has been selected via the PLC (cause 2).

Remedy:

•

Automatically reset if Motor CW and Motor CCW are deactivated

again (in response to cause 1) or

•

If a valid parameter set (PS 1 - 3) is set again (in response to

cause 2).

Bypass element protective tripping

(devices with product version

≥

*E07*)

A very high current occurs in bypass mode. The tripping operation

depends on the duration of the current and strength of the current.

Fault can only be reset after 30 s (for cooling down).
Remedy: Check the motor and check soft starter dimensioning.

Summary of Contents for SIRIUS 3RW44





































































































































































































































































































Search results

Summary of Contents for SIRIUS 3RW44

Reviews:

Related manuals for SIRIUS 3RW44

Brands by name

Popular brands

Siemens SIRIUS 3RW44, Manual

Search results

Summary of Contents for SIRIUS 3RW44

Reviews:

Related manuals for SIRIUS 3RW44

Brands by name

Popular brands