manualshive.com logo in svg

Siemens SIRIUS 3RW44, Manual

The Siemens SIRIUS 3RW44 is a top-of-the-line motor soft starter. This high-performance device ensures a smooth and reliable start, preventing any potential motor damage. Unlock the full potential of your device by downloading the comprehensive user manual for free from manualshive.com. Get instant access to essential insights and operating instructions to make the most out of your Siemens SIRIUS 3RW44 unit.

Share
Download
background image

PROFIBUS DP communication module 

 

9.10 Data formats and data sets 

 

3RW44 soft starters 

180

 

Manual, 03/2017, NEB535219502000/RS-AB/008 

Fault 

No. 

Fault type 

Meaning/cause 

Delete alarm bit/acknowledgement 

F24 

11000:  

Actuator tripping 

•

 

Tripping due to overload 

•

 

Tripping due to zero current 

•

 

Tripping due to asymmetry 

•

 

Tripping due to ground fault 

Alarm bit is always deleted when 

acknowledged with "trip reset". 
Additional acknowledgment in combination 

with another error. 

F26 

11010:  

External fault 

•

 

Overload of the sensor supply 

•

 

Process image error 

Alarm bit is always deleted when 

acknowledged with "trip reset". 

9.10

 

Data formats and data sets 

9.10.1

 

Properties 

The soft starter evaluates a large amount of operating, diagnostic, and statistical data.  

Control data 

Data that is transferred to the soft starter, e.g. motor CCW switching command, trip reset, 

etc.  
Data format: Bit 

Messages 

Data that is transferred from the soft starter and indicates the current operating status, e.g., 

Motor CCW, etc. 
Data format: Bit 

Diagnostics 

Data that is transferred from the soft starter and indicates the current operating status, e.g., 

Overload fault, etc.  
Data format: Bit 

Summary of Contents for SIRIUS 3RW44





































































































































































































































































































Reviews:

No comments

Related manuals for SIRIUS 3RW44

B&R Industries AP1000 User Manual preview
AP1000
Brand: B&R Industries Pages: 89
Danfoss VLT MCD 200 Installation Manual preview
VLT MCD 200
Brand: Danfoss Pages: 32
Danfoss PVG 16 PVH/Covers Technical Information preview
PVG 16 PVH/Covers
Brand: Danfoss Pages: 112
Danfoss PVG 100 Service And Parts Manual preview
PVG 100
Brand: Danfoss Pages: 44
Danfoss PVG 16 PVH/Covers Service And Parts Manual preview
PVG 16 PVH/Covers
Brand: Danfoss Pages: 144
Danfoss VLT LCP 11 Installation Instructions preview
VLT LCP 11
Brand: Danfoss Pages: 2
Danfoss VLT FC Series Operating Instructions Manual preview
VLT FC Series
Brand: Danfoss Pages: 64
Danfoss EKC 102A Instructions Manual preview
EKC 102A
Brand: Danfoss Pages: 8
Danfoss VLT AutomationDrive FC 360 Programming Manual preview
VLT AutomationDrive FC 360
Brand: Danfoss Pages: 60
Danfoss DHP-A Installation Instruction preview
DHP-A
Brand: Danfoss Pages: 6
Danfoss AMV 110 NL AQT Datasheet preview
AMV 110 NL AQT
Brand: Danfoss Pages: 4
Danfoss VLT FC Series Installation Manual preview
VLT FC Series
Brand: Danfoss Pages: 8
Danfoss AK-CC 550A Troubleshooting Manuallines preview
AK-CC 550A
Brand: Danfoss Pages: 2
Danfoss ECL Comfort 110 Quick Manual preview
ECL Comfort 110
Brand: Danfoss Pages: 2
Danfoss 103E5 Installation & User'S Instructions preview
103E5
Brand: Danfoss Pages: 24
Danfoss vlt soft starter mcd 500 Operating Instruction preview
vlt soft starter mcd 500
Brand: Danfoss Pages: 95
Danfoss EKE 347 Installation Manual preview
EKE 347
Brand: Danfoss Pages: 12
Danfoss VLT 5000 Instruction Manual preview
VLT 5000
Brand: Danfoss Pages: 33

Brands by name

Popular brands

Load more brands