Siemens SIRIUS 3RW44 Manual Download Page 278

Page: 278 / 292

General technical data

11.3 Technical data

3RW44 soft starters

278

Manual, 03/2017, NEB535219502000/RS-AB/008

Version

Article No.

Communication modules

3RW4900-0KC00

PROFIBUS communication module
For 3RW44 soft starter integration in the PROFIBUS

network with DPV1 slave functionality. With firmware

version E04 and higher (or date of manufacture May

1, 2009 and later) of the module, DPV1 operation of

the soft starter on a Y-link is also possible (only

DPV0 operation possible with < E04).

3RW4900-0KC00

3RW4900-0NC00

PROFINET communication module
For 3RW44 soft starter integration in the PROFINET

network, suitable for devices with firmware version

E12 or higher

3RW4900-0NC00

External display and operator module

3RW4900-0AC00

For indicating and operating the functions provided

by the soft starter using an externally mounted

display and operator module in IP54 degree of

protection (e.g. in the control cabinet door)

Connecting cable
From the device interface (serial) of the 3RW44 soft

starter to the external display and operator module

Length 0.5 m, flat

3UF7932-0AA00-0

Length 0.5 m, round

3UF7932-0BA00-0

Length 1.0 m, round

3UF7937-0BA00-0

Length 2.5 m, round

3UF7933-0BA00-0

Summary of Contents for SIRIUS 3RW44





































































































































































































































































































Search results

Summary of Contents for SIRIUS 3RW44

Reviews:

Related manuals for SIRIUS 3RW44

Brands by name

Popular brands

Siemens SIRIUS 3RW44, Manual

Search results

Summary of Contents for SIRIUS 3RW44

Reviews:

Related manuals for SIRIUS 3RW44

Brands by name

Popular brands