Siemens SIRIUS 3RW44 Manual Download Page 198

Page: 198 / 292

PROFIBUS DP communication module

9.12 Data sets (BS)

3RW44 soft starters

198

Manual, 03/2017, NEB535219502000/RS-AB/008

ID No.

Byte

Bit

Alarm bit

Error

No.

Meaning/acknowledgment

366

Parameters cannot be changed in ON state

Attempted parameter change while

motor is running or during relevant

device function, which has caused

the trip.
Alarm bit is always deleted when

acknowledged with "Trip Reset" or

valid parameters have been

received.

368

Parameters disabled CPU/master active

Alarm bit is updated continually, soft

starter ignores parameters from the

PLC.

4-7

Reserved = 0

Device functions

0-2

Reserved = 0

369

Factory settings restored

Alarm bit is always deleted when

acknowledged with "trip reset".

4-7

Reserved = 0

367

Incorrect parameter number (low byte)

In conjunction with bytes 81 and 82,

specifies the ID No. of the first

parameter not accepted.
Alarm bit is always deleted when

acknowledged with "trip reset".

Incorrect parameter number (high byte)

0-1

Reserved = 0

1421

Impermissible I

/CLASS setting

3-7

Reserved = 0

1449

Parameter set 1 active

1450

Parameter set 2 active

1451

Parameter set 3 active

Reserved = 0

1453

Parameter set change impermissible

5-7

Reserved = 0

0-1

Reserved = 0

1404

Motor heating active

1402

DC braking active

1403

Dynamic DC braking active

1471

Star/delta motor connection

1472

Inside-delta motor connection

1473

Motor connection type unknown

1408

No load

Reserved = 0

1409

Phase failure L1

1410

Phase failure L2

1411

Phase failure L3

1412

Rotational direction of line frequency right

Summary of Contents for SIRIUS 3RW44





































































































































































































































































































Search results

Summary of Contents for SIRIUS 3RW44

Reviews:

Related manuals for SIRIUS 3RW44

Brands by name

Popular brands

Siemens SIRIUS 3RW44, Manual

Search results

Summary of Contents for SIRIUS 3RW44

Reviews:

Related manuals for SIRIUS 3RW44

Brands by name

Popular brands