Siemens SIRIUS 3RW44 Manual Download Page 197

Page: 197 / 292

PROFIBUS DP communication module

9.12 Data sets (BS)

3RW44 soft starters
Manual, 03/2017, NEB535219502000/RS-AB/008

197

ID No.

Byte

Bit

Alarm bit

Error

No.

Meaning/acknowledgment

361

Trip reset successful

Alarm bit is deleted by an update or

by a "Trip Reset" in ready for

operation status.

362

Trip reset not possible

Tripping cause is still present.
Alarm bit is deleted by an update

(new "Trip Reset") or by a "Trip

Reset" in ready for operation status.

363

Maximum pointer deleted

Alarm bit is always deleted when

acknowledged with "trip reset".

317

Electronics supply

voltage too low

Alarm bit is deleted automatically

when the cause of tripping has

been eliminated.

Communication
303

Bus fault

Watchdog timer of DP interface has

elapsed, alarm bit is updated

continually.

356

CPU/Master STOP

PLC program is no longer being

executed, alarm bit is updated

continually.

357

Automatic mode

Automatic (PLC controlled), alarm

bit is updated continually.

358

Manual bus mode

Manual mode via fieldbus (HMI

controls), alarm bit is updated

continually.

359

Manual mode local

Manual mode via local device

interface, (HMI controls), alarm bit

is updated continually.

Reserved = 0

360

Connection abort in manual mode local

During manual mode, the related

communication connection was

interrupted, alarm bit is updated

continually.

355

Process image error

F26, F24 Process image of the outputs

contains an impermissible bit

combination.
Alarm bit is deleted automatically

when the cause of tripping has

been eliminated.

Parameters
364

Parameter assignment active

Alarm bit is updated continually.

365

Invalid parameter value

F16

Alarm bit is always deleted when

acknowledged with "Trip Reset" or

valid parameters have been

received.

Summary of Contents for SIRIUS 3RW44





































































































































































































































































































Search results

Summary of Contents for SIRIUS 3RW44

Reviews:

Related manuals for SIRIUS 3RW44

Brands by name

Popular brands

Siemens SIRIUS 3RW44, Manual

Search results

Summary of Contents for SIRIUS 3RW44

Reviews:

Related manuals for SIRIUS 3RW44

Brands by name

Popular brands