manualshive.com logo in svg

Siemens SIRIUS 3RW44, Manual

The Siemens SIRIUS 3RW44 is a top-of-the-line motor soft starter. This high-performance device ensures a smooth and reliable start, preventing any potential motor damage. Unlock the full potential of your device by downloading the comprehensive user manual for free from manualshive.com. Get instant access to essential insights and operating instructions to make the most out of your Siemens SIRIUS 3RW44 unit.

Share
Download
background image

PROFIBUS DP communication module 

 

9.12 Data sets (BS) 

 

3RW44 soft starters 

196

 

Manual, 03/2017, NEB535219502000/RS-AB/008 

ID No. 

Byte

Bit

 

Alarm bit 

Error 

No.

*)

 

Meaning/acknowledgment 

341 

4

1

 

Asymmetry tripping 

F24 

Tripping of the motor due to 

asymmetry. 
Alarm bit is automatically deleted 

when the cause of the fault has 

been removed and acknowledged 

with "trip reset". 

334 

4

2

 

I

e

 limit value overshot 

F7 

Limit exceeded, alarm bit is updated 

continually. 

335 

4

3

 

I

e

 limit value undershot 

F8 

Limit undershot, alarm bit is 

updated continually. 

336 

4

4

 

I

e

 current limit tripping 

F24 

Alarm bit is automatically deleted 

when the cause of the fault has 

been removed and acknowledged 

with "trip reset". 

 

4

5

 

Reserved = 0 

- 

 

 

4

6

 

Reserved = 0 

- 

 

339 

4

7

 

Motor stalled - switched off 

F24 

Trip, stalling current detected for 

longer than the permitted stalling 

time.  
Alarm bit is automatically deleted 

when the cause of the fault has 

been removed and acknowledged 

with "trip reset". 

344 

5

0

 

Input 1 

- 

States of the inputs 
"1" = active, HIGH level is present 
"0" = inactive, LOW level is present 
Alarm bit is updated continually. 

345 

5

1

 

Input 2 

- 

346 

5

2

 

Input 3 

- 

347 

5

3

 

Input 4 

- 

 

5

4-7

 

Reserved = 0 

- 

 

342 

6

0

 

Ground fault detected 

- 

Ground fault is present, alarm bit is 

updated continually. 

343 

6

1

 

Ground fault tripping 

F24 

Tripping of the motor due to ground 

fault. 
Alarm bit is automatically deleted 

when the cause of the fault has 

been removed and acknowledged 

with "trip reset". 

353 

6

2

 

Quick stop active 

F26, F24  Tripping of the motor due to quick 

stop. 
Alarm bit is automatically deleted 

when the cause of the fault has 

been removed and acknowledged 

with "trip reset". 

 

6

3

 

Reserved = 0 

- 

 

Summary of Contents for SIRIUS 3RW44





































































































































































































































































































Reviews:

No comments

Related manuals for SIRIUS 3RW44

KAR-TECH MICRO Installation And Operation Manual preview
MICRO
Brand: KAR-TECH Pages: 28
2iB SC10 Quick Start Manual preview
SC10
Brand: 2iB Pages: 5
2gig Technologies Go!Control Panel Installation & Programming Manual preview
Go!Control Panel
Brand: 2gig Technologies Pages: 78
Danfoss VLT AQUA Drive FC 202 Installation Manual preview
VLT AQUA Drive FC 202
Brand: Danfoss Pages: 124
Danfoss AME 55 Installation Manual preview
AME 55
Brand: Danfoss Pages: 2
Danfoss AME 110 NL Datasheet preview
AME 110 NL
Brand: Danfoss Pages: 8
Danfoss AK-CH 650 User Manual preview
AK-CH 650
Brand: Danfoss Pages: 114
Danfoss TS715Si Installation Manual preview
TS715Si
Brand: Danfoss Pages: 16
Danfoss AME 438 SU Installation Manual preview
AME 438 SU
Brand: Danfoss Pages: 24
Danfoss AK-LM 330 User Manual preview
AK-LM 330
Brand: Danfoss Pages: 8
Danfoss ECL Comfort 296 Operating Manual preview
ECL Comfort 296
Brand: Danfoss Pages: 159
Danfoss VLT AutomationDrive FC 301 Operating Manual preview
VLT AutomationDrive FC 301
Brand: Danfoss Pages: 78
Danfoss AME 335 Installation Manual preview
AME 335
Brand: Danfoss Pages: 20
Danfoss ECL Comfort 210 User Manual preview
ECL Comfort 210
Brand: Danfoss Pages: 12
Danfoss ECL Comfort 110 Mounting Manual preview
ECL Comfort 110
Brand: Danfoss Pages: 8
Danfoss AFQM Operating Manual preview
AFQM
Brand: Danfoss Pages: 16
Danfoss CCR2 Installation Manual preview
CCR2
Brand: Danfoss Pages: 64
Easy-Laser E540 Manual preview
E540
Brand: Easy-Laser Pages: 84

Brands by name

Popular brands

Load more brands