Siemens SIRIUS 3RW44 Manual Download Page 258

Page: 258 / 292

General technical data

11.3 Technical data

3RW44 soft starters

258

Manual, 03/2017, NEB535219502000/RS-AB/008

General supplementary conditions
Maximum starting time:

10 s

Current limiting

300 %

Starts/hour

ON time

30%

Assembly type

Stand-alone installation

Installation altitude

Max. 1000 m/3280 ft

Ambient temperature

•

kW: 40 °C/104 °F

•

hp: 50 °C/122 °F

The listed motor ratings are only approximate values. The soft starter should always be

designed on the basis of the motor current (rated operational current). A larger model may

need to be selected for different conditions.
Motor output ratings are based on DIN 42973 (kW) and NEC 96/UL508 (hp).

Design with Simulation Tool for Soft Starters (STS)

For dimensioning soft starters under other supplementary conditions, also for heavy starting

up to CLASS 30, we recommend our Simulation Tool for Soft Starters (STS):

https://support.industry.siemens.com/cs/ww/en/view/101494917 or our Technical Assistance:

Tel.: +49 (0) 911-895-5900, e-mail: [email protected]

Summary of Contents for SIRIUS 3RW44





































































































































































































































































































Search results

Summary of Contents for SIRIUS 3RW44

Reviews:

Related manuals for SIRIUS 3RW44

Brands by name

Popular brands

Siemens SIRIUS 3RW44, Manual

Search results

Summary of Contents for SIRIUS 3RW44

Reviews:

Related manuals for SIRIUS 3RW44

Brands by name

Popular brands