manualshive.com logo in svg

Siemens SIRIUS 3RW44, Manual

The Siemens SIRIUS 3RW44 is a top-of-the-line motor soft starter. This high-performance device ensures a smooth and reliable start, preventing any potential motor damage. Unlock the full potential of your device by downloading the comprehensive user manual for free from manualshive.com. Get instant access to essential insights and operating instructions to make the most out of your Siemens SIRIUS 3RW44 unit.

Share
Download
background image

 

PROFIBUS DP communication module 

 

9.12 Data sets (BS) 

3RW44 soft starters 
Manual, 03/2017, NEB535219502000/RS-AB/008 

195

 

ID No. 

Byte

Bit

 

Alarm bit 

Error 

No.

*)

 

Meaning/acknowledgment 

302 

0

6

 

Group fault 

- 

At least 1 error that generates an E 

No. is set.  
Alarm bit is deleted when the cause 

of tripping has been eliminated and 

acknowledged with "trip reset, auto 

reset, OFF command" 

304 

0

7

 

Group warning 

- 

At least 1 warning is pending, alarm 

bit is updated continually. 

 

1

0

 

Reserved = 0 

- 

 

319 

1

1

 

No supply voltage 

F17, F24  Alarm bit is automatically deleted 

when the cause of the fault has 

been removed and acknowledged 

with "trip reset". 

 

1

2

 

Reserved = 0 

- 

 

312 

1

3

 

Starting active 

- 

Alarm bit is updated continually. 

313 

1

4

 

Coast down active 

- 

 

1

5

 

Reserved = 0 

- 

 

316 

1

6

 

Electrical braking active 

- 

Brake output is switched on by the 

soft starter, alarm bit is updated 

continually. 

314 

1

7

 

Slow speed active 

- 

Alarm bit is updated continually. 

Protective function: Motor/cable/ short-circuit 
324 

2

0

 

Temperature sensor overload 

F4 

Overload detected, alarm bit is 

updated continually. 

325 

2

1

 

Temperature sensor wire break 

F6 

Thermistor circuit interrupted, alarm 

bit is updated continually. 

326 

2

2

 

Temperature sensor short-circuit 

F1 

Short-circuit in thermistor circuit, 

alarm bit is updated continually. 

327 

2

3

 

Thermal motor model overload 

F4 

Overload detected, alarm bit is 

updated continually. 

328 

2

4

 

Overload tripping 

F24 

Motor is tripped due to a detected 

overload.  
Alarm bit is automatically deleted 

when the cause of the fault has 

been removed and acknowledged 

with "trip reset"/"auto reset". 

329 

2

5

 

Idle time active 

- 

Alarm bit is updated continually. 

330 

2

6

 

Cooling time active 

- 

Alarm bit is updated continually. 

 

2

7

 

Reserved = 0 

- 

 

 

3

0-6

 

Reserved = 0 

- 

 

352 

3

7

 

Input control 

- 

Device receives control commands 

via the inputs, alarm bit is updated 

continually. 

340 

4

0

 

Asymmetry detected 

- 

Asymmetry is present, alarm bit is 

updated continually. 

Summary of Contents for SIRIUS 3RW44





































































































































































































































































































Reviews:

No comments

Related manuals for SIRIUS 3RW44

Eaton AMPGARD RVSS Instruction For Installation And Maintenance preview
AMPGARD RVSS
Brand: Eaton Pages: 16
NEC N8403-019 User Manual preview
N8403-019
Brand: NEC Pages: 146
BEIER-Electronic SV1-2-10Z Instruction Manual preview
SV1-2-10Z
Brand: BEIER-Electronic Pages: 22
Wavelink Avalanche User Manual preview
Avalanche
Brand: Wavelink Pages: 69
Bang & Olufsen Beo4 Getting Started preview
Beo4
Brand: Bang & Olufsen Pages: 80
Bang & Olufsen Beo4 Manual preview
Beo4
Brand: Bang & Olufsen Pages: 13
Campbell CELL200 Series Quick Deploy Manual preview
CELL200 Series
Brand: Campbell Pages: 3
EMS ZITON RADIO LOOP MODULE Programming Manual preview
ZITON RADIO LOOP MODULE
Brand: EMS Pages: 26
Danfoss 084B8012 Instructions Manual preview
084B8012
Brand: Danfoss Pages: 30
Rational MI-2063 Modification Instruction preview
MI-2063
Brand: Rational Pages: 140
Pangolin FB4 Series User Manual preview
FB4 Series
Brand: Pangolin Pages: 35
H.E. Anderson Ratio Feeder J+ Advanced Series Manual preview
Ratio Feeder J+ Advanced Series
Brand: H.E. Anderson Pages: 11
Barthelme Chromoflex Pro Series Instruction Manual preview
Chromoflex Pro Series
Brand: Barthelme Pages: 6
Kohzu Precision RC-010 Manual preview
RC-010
Brand: Kohzu Precision Pages: 58
Danfoss AME 15 QM Instructions Manual preview
AME 15 QM
Brand: Danfoss Pages: 14
Variotech ENA3 Manual preview
ENA3
Brand: Variotech Pages: 24
Sunlight Supply TITAN CONTROLS KRONUS 2 Instruction Manual preview
TITAN CONTROLS KRONUS 2
Brand: Sunlight Supply Pages: 4
Danfoss ECL Comfort 300 User Manual preview
ECL Comfort 300
Brand: Danfoss Pages: 75

Brands by name

Popular brands

Load more brands