manualshive.com logo in svg

Siemens SIRIUS 3RW44, Manual

The Siemens SIRIUS 3RW44 is a top-of-the-line motor soft starter. This high-performance device ensures a smooth and reliable start, preventing any potential motor damage. Unlock the full potential of your device by downloading the comprehensive user manual for free from manualshive.com. Get instant access to essential insights and operating instructions to make the most out of your Siemens SIRIUS 3RW44 unit.

Share
Download
background image

PROFIBUS DP communication module 

 

9.1 Introduction 

 

3RW44 soft starters 

150

 

Manual, 03/2017, NEB535219502000/RS-AB/008 

Requirements 

●

 

You have configured an infeed module with integrated S7 station, e.g. with CPU315-2 

DP. 

●

 

STEP 7 (V 5.1 or  hotfix 2) is fully installed on your PC or programming device. 

●

 

You are proficient in STEP 7. 

 

 

 

NOTICE 

The PROFIBUS DP communication module can only be operated on 3RW44 devices 

with product version "E12" or higher, implemented for devices from production date 

130601 onwards.  

 

 

 

 

 

NOTICE 

IT systems with ground-fault monitoring:  

3RW44, product version ≤ *E06* and 

the PROFIBUS DP communication module must 

not be used in this network configuration. 3RW44 soft starters from product version 

*E07* onwards can be used in combination with the communication module. However, 

the phase voltage values (UL-N) and phase-to-phase voltage values (UL-L) may be 

displayed incorrectly on the measured value display of the 3RW44. 

 

 

 

NOTICE 

For 3RW44 PROFIBUS DP communication module with product version < *E03*: 
use of the 3RW44 with PROFIBUS on redundant controllers and Y-Link: 

The 3RW44 acts like a DPV0 slave on Y-link. Parameter assignment is only possible via 

the GSD file and only cyclic data is transmitted, no data sets or alarms. 
For 3RW44 PROFIBUS DP communication module, product version *E04* or higher:  
As from this version, DPV1 operation (read/write data sets and alarms) is also possible 

downstream from a Y-link. 

 

Summary of Contents for SIRIUS 3RW44





































































































































































































































































































Reviews:

No comments

Related manuals for SIRIUS 3RW44

TA Hydronics STS Technical Description preview
STS
Brand: TA Hydronics Pages: 14
Unitech RM300 SDK User Manual preview
RM300 SDK
Brand: Unitech Pages: 11
B meters IWM-PL4 Quick User Manual preview
IWM-PL4
Brand: B meters Pages: 10
Barco Argus Information preview
Argus
Brand: Barco Pages: 6
Rachio IRO Installation Manual preview
IRO
Brand: Rachio Pages: 2
Yamaha RCX240 Supporting Supplement Manual preview
RCX240
Brand: Yamaha Pages: 92
OPW PetroVend PV200 Options Installation preview
PetroVend PV200
Brand: OPW Pages: 2
RKC INSTRUMENT X-TIO-R Instruction Manual preview
X-TIO-R
Brand: RKC INSTRUMENT Pages: 10
IFM EC2121 System Manual preview
EC2121
Brand: IFM Pages: 41
Duco iAV Quick Start Manual preview
iAV
Brand: Duco Pages: 16
LEGRAND MRD6 v2 Installation Instructions Manual preview
MRD6 v2
Brand: LEGRAND Pages: 10
VAT 642 Series Installation, Operating, & Maintenance Instructions preview
642 Series
Brand: VAT Pages: 94
Intiel Dynamic Boiler Controller User Manual preview
Dynamic Boiler Controller
Brand: Intiel Pages: 25
M-system R3-PA8 Instruction Manual preview
R3-PA8
Brand: M-system Pages: 3
Malossi FORCE MASTER 2.1 Assembly Instructions Manual preview
FORCE MASTER 2.1
Brand: Malossi Pages: 46
IGD TOC-750S-CBF Operation Manual preview
TOC-750S-CBF
Brand: IGD Pages: 13
JBL Six Button Remote User Manual preview
Six Button Remote
Brand: JBL Pages: 5
A-T Controls Triad Controls WE Series Installation And Operation Manual preview
Triad Controls WE Series
Brand: A-T Controls Pages: 13

Brands by name

Popular brands

Load more brands