Siemens SIRIUS 3RW44 Manual Download Page 144

Page: 144 / 292

Diagnostics and messages

8.1 Diagnostics and messages

3RW44 soft starters

144

Manual, 03/2017, NEB535219502000/RS-AB/008

Message

①

②

③

Cause/solution

Prewarning limit - motor heating

Motor heating is greater than the set parameter value: Prewarning limit

- motor heating. The thermal motor model approaches an overload trip

depending on the set value. For heavy starting and set values of

trip

ping class ≥ CLASS 20, we recommend increasing the "Prewarning

limit motor heating" parameter to 95 %.

Remaining time for tripping

undershot

Time up to overload trip of the thermal motor model is shorter than the

set "Prewarning limit - remaining time for tripping" parameter.

In the case of heavy starting and set values of tripping class

≥ CLASS

20, we recommend setting the "Prewarning limit - remaining time for

tripping" parameter value to 0 s (deactivated).

Line overvoltage

(for devices with product version

< *E04*)
Line voltage too high

(for devices with product version

≥

*E04*)

Applied 3-phase line voltage is not suitable for the device or prolonged

voltage peaks arise.

Tripping is caused by exceeding of the permissible rated control supply

voltage of >10 % >500 ms. As from product version *E02*, the internal

threshold for tripping has been increased to >18 % >2000 ms.
Remedy: Apply the correct voltage.

Current measuring range overshot

A very high current has occurred (above the measuring range of the

current transformers integrated in the soft starter). This can occur in

the event of: direct-on-line starting, breakaway pulse or combined

braking.
Remedy: In the case of the "Voltage ramp" start type, extend the

set ramp time and reduce the breakaway voltage or the braking

torque. The soft starter is possibly dimensioned too small for the

motor.

If the message occurs during starting, it may have been generated

erroneously by a too-frequently generated "Prewarning limit - motor

heating", "Remaining time for tripping" or "I

limit

exceeded/undershot" warning (can also be traced via the entries in

the logbook/events).
Remedy: See description of applicable messages.

Trip - motor blocked
(devices with product version

<*E07* only)

A very high current suddenly arises in bypass mode, e.g. if the motor

blocks (I > 4 x I

eMotor

over 100 ms).

Remedy: Check the motor.

Current range exceeded

More than 6 times the device's rated operational current flowed for a

prolonged period.
Remedy: Activate current limiting or check dimensioning (device and

motor).

Power unit overheated

x x Overload trip of the thermal model for the power unit

Remedy: Wait until the device has cooled down again, possibly set

lower current limiting for starting, or reduce the switching frequency (too

many consecutive starts).

Check whether the motor is blocked or whether the ambient

temperature in the soft starter's environment is too high (derating as

from 40 °C; see chapter Technical data (Page 253)).

Power unit overtemperature

Temperature of the thermal model for the power unit is above the

allowed continuous operating temperature.
Remedy: Check the motor's operational current or check whether the

ambient temperature in the soft starter's environment is too high

(derating as from 40 °C; see chapter Technical data (Page 253)).

Summary of Contents for SIRIUS 3RW44





































































































































































































































































































Search results

Summary of Contents for SIRIUS 3RW44

Reviews:

Related manuals for SIRIUS 3RW44

Brands by name

Popular brands

Siemens SIRIUS 3RW44, Manual

Search results

Summary of Contents for SIRIUS 3RW44

Reviews:

Related manuals for SIRIUS 3RW44

Brands by name

Popular brands