manualshive.com logo in svg

Segway SE-3 Patroller, Service Manual

The Segway SE-3 Patroller is a versatile and efficient three-wheeled vehicle designed for security and law enforcement professionals. For detailed maintenance and servicing instructions, download the free Service Manual from manualshive.com. Ensure peak performance and longevity of your SE-3 Patroller with this essential manual.

Share
Download
background image

SE-3 Patroller

vi

Lights ................................................................................................................................... 33

Headlight ..................................................................................................................................................... 34
Headlight Alignment ................................................................................................................................... 35
Accessing the Light Cluster ........................................................................................................................ 36
Front Strobe Light ........................................................................................................................................37
Side Strobe Light ........................................................................................................................................ 38
Front Directional Light ................................................................................................................................ 39
Brake Light .................................................................................................................................................. 40
Rear Directional Light ..................................................................................................................................41
Rear Strobe Light ........................................................................................................................................ 42

Battery Compartment ........................................................................................................43

Battery Slides .............................................................................................................................................. 44
Battery Bumpers ......................................................................................................................................... 45

Bib Panel Components ....................................................................................................... 47

Glove Box Door ............................................................................................................................................ 48
KeyLock ....................................................................................................................................................... 49
Accessory Power Outlet .............................................................................................................................. 50

Brakes ...................................................................................................................................51

Brake Fluid ................................................................................................................................................... 52
Draining Brake Lines ................................................................................................................................... 53
Bleeding Brake Lines .................................................................................................................................. 54
Front Caliper ................................................................................................................................................ 56
Front Rotor .................................................................................................................................................. 58
Master Cylinder ........................................................................................................................................... 59
Brake Lever .................................................................................................................................................. 60
Rear Caliper & Rotor ................................................................................................................................... 62
Front Brake Line .......................................................................................................................................... 64
Rear Brake Line ........................................................................................................................................... 66

Controls ...............................................................................................................................69

UI Module .................................................................................................................................................... 70
UI Housing .................................................................................................................................................... 71
Control Cluster .............................................................................................................................................72
Throttle .........................................................................................................................................................74
Handlebar Grip .............................................................................................................................................76

Contents

Summary of Contents for SE-3 Patroller





















































































































































Reviews:

No comments

Related manuals for SE-3 Patroller

Yamaha DRIVE 2 EFI 2019 Operator'S Manual preview
DRIVE 2 EFI 2019
Brand: Yamaha Pages: 52
Dynacraft 12V DUNE BUGGY Owner'S Manual preview
12V DUNE BUGGY
Brand: Dynacraft Pages: 33
I-Motioncaddys im4 Range 2013 Manual preview
im4 Range 2013
Brand: I-Motioncaddys Pages: 16
Star EV Roadster 2+2-AC Owner'S Manual And Service Manual preview
Roadster 2+2-AC
Brand: Star EV Pages: 16

Brands by name

Popular brands

Load more brands