Segway SE-3 Patroller Service Manual Download Page 130

Page: 130 / 148

SE-3 Patroller

122

Accessory Power Harness

This harness connects to the Accessory Power Outlet on the
Bib Panel. It provides 12 V power.

Tools Required:

Wire cutters

Removal

1. Make sure the SE-3 Patroller is powered off,

unplugged, and the parking brake is engaged.

2. Remove the following components:

a. Battery Module (

page 8

)

b. Storage Trays (

page 13

)

c. Bib Panel (

page 14

)

d. Glove Box (

page 16

)

3. Disconnect the wire harness from the PI Board.

See

Figure 169

NOTICE

You do not need to remove the Electronics Shield to
access the Accessory Power Harnesses.

4. Using a pair of wire cutters, remove the two cable ties

around the frame.

5. Using a pair of wire cutters, remove the cable tie

holding the harness to the top of the frame.

6. Remove the Accessory Power Harness.

Installation

1. Make sure the SE-3 Patroller is powered off,

unplugged, and the parking brake is engaged.

2. Connect the wire harness to the PI Board.

See

Figure 169

3. Route the harness around the right side of the frame,

and up to the top left of the frame. See

Figure 170

4. Install three cable ties:

a. One at the top of the frame.
b. Two holding the harness to the frame.

5. Install the following components:

a. Glove Box (

page 16

)

b. Bib Panel (

page 14

)

c. Storage Trays (

page 13

)

d. Battery Module (

page 8

)

6. Perform post-service tests (

page 127

Figure 169: Accessory Power Harness to PI Board

Figure 170: Accessory Power Harness Routing

Harnesses

Summary of Contents for SE-3 Patroller





















































































































































Search results

Summary of Contents for SE-3 Patroller

Reviews:

Related manuals for SE-3 Patroller

Brands by name

Popular brands

Segway SE-3 Patroller, Service Manual

Search results

Summary of Contents for SE-3 Patroller

Reviews:

Related manuals for SE-3 Patroller

Brands by name

Popular brands