Segway SE-3 Patroller Service Manual Download Page 121

Page: 121 / 148

Service Manual

113

Installation

1. Make sure the SE-3 Patroller is powered off,

unplugged, and the parking brake is engaged.

2. Connect the wire harness to the Control Cluser,

Headlight, Throttle, and both Brake Levers.
Right Brake Lever
Grey Red/Black
Black Orange/Black
Left Brake Lever
Grey Grey/White
Black Brown/Black

3. Route the harness around the left side of the frame.
4. Connect the wire harness to the PI Board.

See

Figure 151

5. Install three cable ties:

a.  Harnesses on the steering column.
b.  This harness to the User Interface Harness.
c.  This harness to the frame.

6. Install the following components:

a. Electronics Shield (

page 100

)

b. Front Cowl (

page 17

)

c. Glove Box (

page 16

)

d. Bib Panel (

page 14

)

e. Storage Trays (

page 13

)

f. Battery Module (

page 8

)

7. Perform post-service tests (page 127).

Figure 153: Handlebar Controls Harness on the Steering Column

Harnesses

Summary of Contents for SE-3 Patroller





















































































































































Search results

Summary of Contents for SE-3 Patroller

Reviews:

Related manuals for SE-3 Patroller

Brands by name

Popular brands

Segway SE-3 Patroller, Service Manual

Search results

Summary of Contents for SE-3 Patroller

Reviews:

Related manuals for SE-3 Patroller

Brands by name

Popular brands