manualshive.com logo in svg

Segway SE-3 Patroller, Service Manual

Share
Download
Segway SE-3 Patroller Service Manual Download Page 58

SE-3 Patroller

50

Accessory Power Outlet

Tools Required:

 None

Removal

1.  Make sure the SE-3 Patroller is powered off, 

unplugged, and the parking brake is engaged.

2.  Remove the following components:

a.  Battery Module (

page 8

)

b.  Storage Trays (

page 13

)

c.  Bib Panel (

page 14

)

3.  Unscrew the plastic nut on the back of the Accessory 

Power Outlet. See 

Figure 65

.

4.  Remove the Accessory Power Outlet.

Installation

1.  Make sure the SE-3 Patroller is powered off, 

unplugged, and the parking brake is engaged.

2.  Insert the Accessory Power Outlet through the hole 

on the left hand side of the Bib Panel.

3.  Thread the plastic nut onto the back of the Accessory 

Power Outlet. 
Tighten finger tight, then turn an additional 1/8 turn.

4.  Install the following components:

a.  Bib Panel (

page 14

)

b.  Storage Trays (

page 13

)

c.  Battery Module (

page 8

)

5.  Perform any post-service tests (

page 127

).

Figure 65:  Accessory Power Outlet

Accessory Power Outlet
(23979-00001)

Nut

Bib Panel Components

Summary of Contents for SE-3 Patroller





















































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands