Segway SE-3 Patroller Service Manual Download Page 119

Page: 119 / 148

Service Manual

111

Installation

1. Make sure the SE-3 Patroller is powered off,

unplugged, and the parking brake is engaged.

2.  Connect the Drive Harness to the Motor Controller.
3.  Connect the Drive Harness to the Motor.
4.  Feed the harness through the hole in the front of the

motor cavity. Send the Left Drive Harness out the left
side of the frame. Send the Right Drive Harness out
the right side of the frame.

5. Feed the harness under the horizontal brace on

the frame (see

Figure 150

) and connect it to the PI

Board.

6. Install two cable ties around the harnesses in the

motor cavity.

7. Install two cable ties around the harnesses on the

side of the frame.

8. Install the following components:

a. Motor Cavity Lid (

page 89

)

b. Rider Detect Mat (

page 82

)

c. Electronics Shield (

page 100

)

d. Side Panel (

page 20

)

e. Light Cluster (

page 18

)

f. Front Cowl (

page 17

)

g. Glove Box (

page 16

)

h. Bib Panel (

page 14

)

Storage Trays (

page 13

)

Battery Module (

page 8

)

9. Perform post-service tests (

page 127

Harnesses

Figure 150: Drive Harness Routing

Brace

Summary of Contents for SE-3 Patroller





















































































































































Search results

Summary of Contents for SE-3 Patroller

Reviews:

Related manuals for SE-3 Patroller

Brands by name

Popular brands

Segway SE-3 Patroller, Service Manual

Search results

Summary of Contents for SE-3 Patroller

Reviews:

Related manuals for SE-3 Patroller

Brands by name

Popular brands