Segway SE-3 Patroller Service Manual Download

Page: 124 / 148

SE-3 Patroller

116

Light Cluster Harness

This harness connects the PI Board to the directional lights
and the strobe lights in the Light Cluster.

Tools Required:

Wire cutters

Removal

1. Make sure the SE-3 Patroller is powered off,

unplugged, and the parking brake is engaged.

2. Remove the following components:

a. Battery Module (

page 8

)

b. Storage Trays (

page 13

)

c. Bib Panel (

page 14

)

d. Glove Box (

page 16

)

e. Front Cowl (

page 17

)

f. Electronics Shield (

page 100

)

3. Disconnect the wire harness from the PI Board.

See

Figure 158

4. Using a pair of wire cutters, remove the cable tie

connecting the harness to the frame.

5. Using a pair of wire cutters, remove the cable ties

around the harness inside the Light Cluster.

6. Disconnect the wire harness from the lights.

See

Figure 159

7. Remove the Light Cluster Harness.

Figure 158: Light Cluster Harness to PI Board

Strobe Lights

(Order Not Important)

Right

Directional Light

Left

Directional Light

Figure 159: Light Cluster Harness Connectors

Front Lights

Harnesses

Summary of Contents for SE-3 Patroller





















































































































































Search results

Summary of Contents for SE-3 Patroller

Reviews:

Related manuals for SE-3 Patroller

Brands by name

Popular brands

Segway SE-3 Patroller, Service Manual

Search results

Summary of Contents for SE-3 Patroller

Reviews:

Related manuals for SE-3 Patroller

Brands by name

Popular brands