Segway SE-3 Patroller Service Manual Download Page 133

Page: 133 / 148

Service Manual

125

Service Interface Harness

This harness is used by service technicians when diagnosing
problems with the SE-3 Patroller.

Tools Required:

Wire cutters

Removal

1. Make sure the SE-3 Patroller is powered off,

unplugged, and the parking brake is engaged.

2. Remove the following components:

a. Battery Module (

page 8

)

b. Storage Trays (

page 13

)

c. Bib Panel (

page 14

)

d. Glove Box (

page 16

)

e. Electronics Shield (

page 100

)

3. Disconnect the wire harness from the PI Board.

See

Figure 175

4. Remove the Service Interface Harness.

Installation

1. Make sure the SE-3 Patroller is powered off,

unplugged, and the parking brake is engaged.

2. Connect the wire harness to the PI Board.

See

Figure 175

3. Install the following components:

a. Electronics Shield (

page 100

)

b. Glove Box (

page 16

)

c. Bib Panel (

page 14

)

d. Storage Trays (

page 13

)

e. Battery Module (

page 8

)

4. Perform post-service tests (

page 127

Figure 175: Service Interface Harness to PI Board

Service

Port

Harnesses

Summary of Contents for SE-3 Patroller





















































































































































Search results

Summary of Contents for SE-3 Patroller

Reviews:

Related manuals for SE-3 Patroller

Brands by name

Popular brands

Segway SE-3 Patroller, Service Manual

Search results

Summary of Contents for SE-3 Patroller

Reviews:

Related manuals for SE-3 Patroller

Brands by name

Popular brands