manualshive.com logo in svg

Schaerer Coffee Art TouchIT, Programming Manual, Page: 26 / 154

Share
Download
Schaerer Coffee Art TouchIT Programming Manual Download Page 26

www.schaerer.com

Basic operation

PASCA_TOUCHIT_EN

V02 | 07.2013

26

Transport conditions

►

Before moving the coffee machine, disconnect the drinking water supply, the power supply 
and the dirty water outlet.

►

Before moving the coffee machine, check the floor for obstacles and uneven areas.

CAUTION!

Risk of machine

damage!

Improper transport of the machine may result in machine damage.
Adhere to the following instructions when moving machines on a cart:

•

For safety reasons, the cart must be pulled and not pushed when moving the coffee ma-
chine.

•

Only pull on the cart and never on the machine.

•

The cart is not intended for transporting cargo.

Switching off

End of operation

►

Perform the daily cleaning routine.

►

Empty the grounds container, clean it and reinstall it.

►

Press the field at the bottom right.

The machine switches to standby.

►

Disconnect the power plug of the machine from the power supply.

The machine is de-energised.

►

Close the stopcock of the drinking water supply.

Option: External drinking and waste water tanks

►

Empty the drinking water tank and rinse it with fresh water.

►

Empty the waste water tank and rinse it thoroughly with fresh water.

Option: Milk system

►

Remove the milk container.

►

Empty and clean the milk container.

CAUTION!

Risk of machine

damage!

There is a risk that the water pump may run dry.
When taking the device back into service, the stopcock of the drinking water supply
must be opened before the machine is switched on.

Lengthy downtimes (more than 1 week)

See "Service technician menu" - "System" - "Chip card service" on changing the PIN.

The manufacturer cannot be held liable for any damage resulting from unintended use of the
cart or from failure to follow the operating instructions.

When the "Switch off after cleaning" parameter is activated, the machine switches off automat-
ically after cleaning.

Failure to do so will result in a loss of warranty coverage in the event of damage.

During extended downtimes, such as during holidays, the machine must be taken out of oper-
ation.

Summary of Contents for Coffee Art TouchIT



























































































































































Reviews:

No comments