SBC PCD2.M5 Series Manual Download Page 60

Page: 60 / 244

Hardware Manual for the PCD2.M5 Series│Document 26/856; Version EN 12│2014-07-24

Saia-Burgess Controls AG

Memory module PCD3.R600 for flash cards (FCs)

PCD2.M5_ Classic CPUs and expansion housings

3-47

● There must be a PC FAT file system (FAT16) on the card in order for the SD card

to be formatted with the SBC file system

● First, all FAT files are deleted, then the SBC file system is installed when the card

is inserted and the BCD switch set to 5

● If the BCD switch is set to 0, the SBC file system (SAIANTFS.FFS) is installed if it

is not already present and the card is empty, i.e. if a new card is installed, it does

not have to be formatted with position 5.

● Not all flash cards have a “write-protect” switch

● The card is inserted into a so-called push-push socket (push to insert and remove)

● Do not remove card when the “Busy” LED is on.

3.13.5 Flash card

SAI

A B

URG

ESS

NTR

OLS

PCD

.7R-

SD2

The SD flash card is not part of the PCD2.R6000 and has to be or

dered separately.

The SD card must be of good quality (industry-standard, as tested by

SBC). Other flash cards can also be used, but they will not be sup

ported and are excluded from any warranty.

To increase service life, the flash cards should not be more than 80% filled for pure

read applications. For read/write applications, no more than 50% of the memory

space should be used.

On the PCD2, a non-standard file system (SBC FS) is used. This means that the

flash cards have to be formatted before being used for the first time. This happens

automatically when a new FAT 16 flash card is inserted into the PCD2.R6000.

Flash card handling

The card is inserted into a so-called push-push socket (push to insert and remove). It

can be removed without switching off the PCD2.

Summary of Contents for PCD2.M5 Series





















































































































































































































































Search results

Summary of Contents for PCD2.M5 Series

Reviews:

Related manuals for PCD2.M5 Series

Brands by name

Popular brands

SBC PCD2.M5 Series, Manual

Search results

Summary of Contents for PCD2.M5 Series

Reviews:

Related manuals for PCD2.M5 Series

Brands by name

Popular brands