SBC PCD2.M5 Series Manual Download Page 193

Page: 193 / 244

Hardware Manual for the PCD2.M5 Series│Document 26/856; Version EN 12│2014-07-24

Saia-Burgess Controls AG

Analogue combined input/output modules

Input/output (I/O) modules

6-83

Filters

●

Inputs

There are two factors used to filter the captured values:

○

The basic hardware filter with a time constant of 2 ms. This filter

attenuates the input signal by 6 dB per order of magnitude at a

switching frequency of 80 Hz.

○

The software also has an effect. This results in a delay to the captured

value of 2 ms with a notch filter property at 500 Hz, where no software-

based filter with 50 Hz/60 Hz has been selected.

Where a 50 Hz (60 Hz) filter is used, the frequency of the notch filter is 50 Hz

(60 Hz); in this case, the delay is also 2 ms.

●

Outputs

Only the hardware-based filer with a time constant of 1 ms is active.

Technical data

Inputs

General:

Resolution:

14 bit

Measurement type:

differential

Number of channels:

Galvanic separation of the PCD:

yes, 500 V

Galvanic separation of external supply:

yes, 500 V

Galvanic separation between channels:

Type of connections:

two cables per channel

Configuration of operating mode:

using DIP switches

Accuracy at 25 °C:

± 0.2% max.

Repeat accuracy:

± 0.05% max.

Temperature drift (0…55 °C) max.:

± 70 ppm/°C

Overvoltage protection:

± 50 V min.

Overcurrent protection:

± 35 mA min.

Common mode max. voltage:

± 50 V min.

Common mode rejection:

70 dB min.

Filter:

Time constant for hardware filter:

2 ms

Attenuation of software-based 50 Hz filter:

40 dB min. between 49.5 and 50.5 Hz

Attenuation of software-based 60 Hz filter:

40 dB min. between 59.5 and 60.5 Hz

Voltage mode:

Resolution range 0

…

10 V mode:

14 Bit; 0.61 mV per LSB

Current mode:

Current shunt resistance:

125

Ω

Resolution range 0

…

20 mA:

14 Bit; 1.22

µA per LSB

Resolution range 4

…

20 mA:

13.7 Bit; 1.22

µA per LSB

Temperature / resistance mode:

Resolution for Pt1000; range -50 …

400 °C

0.1 °C

Resolution for Pt500; range -50 …

400 °C

0.2 °C

Resolution for Ni1000; range -60 …

200 °C

0.1 °C

Resolution for resistor; range 0 …

2500

Ω

0,2

Ω

Shunt capacity for temp sensor / resistor:

2.5 mW max.

Summary of Contents for PCD2.M5 Series





















































































































































































































































Search results

Summary of Contents for PCD2.M5 Series

Reviews:

Related manuals for PCD2.M5 Series

Brands by name

Popular brands

SBC PCD2.M5 Series, Manual

Search results

Summary of Contents for PCD2.M5 Series

Reviews:

Related manuals for PCD2.M5 Series

Brands by name

Popular brands