SBC PCD2.M5 Series Manual Download Page 23

Page: 23 / 244

Hardware Manual for the PCD2.M5 Series│Document 26/856; Version EN 12│2014-07-24

Saia-Burgess Controls AG

PCD2 CPUs

PCD2.M5_ Classic CPUs and expansion housings

3-10

3.4.3 Extensions with various module holders

The PCD2.M5_ controllers can be expanded with PCD2.C2000/C1000 components,

making additional module sockets available. Up to 7 PCD2.C2000/C1000 module

holders can be connected to the PCD2.M5_ . This allows the user to attach a

maximum of 64 I/O modules, or 1023 digital inputs/outputs.

For local expansion, the PCD2 LIO (local I/O) modules can be used.

For decentralized expansion using Profibus, the PCD3 RIO (remote I/O) modules can

be used:

When selecting I/O modules, ensure that the internal 5V and +V supply is not

overloaded.

The PCD2.M5_ controllers can be expanded with PCD2.C2000/C1000, PCD3.Cxx0

or PCD2.C1x0 components, making additional module sockets available:

PCD2.M5_ type

Maximum number of inputs/outputs or I/O module sockets for the system:

Expansion with

PCD2.C2000/C1000 components

1023

1)2)

Expansion with

PCD3.Cxx0 components

1023

1)2)

Expansion with

PCD2.C1xx components

255

1)2)

1) Using digital I/O modules PCD2/3.E16x or A46x with 16 I/Os each
2) On all PCD2 units, address 255 is reserved for the watchdog. The I/Os reserved for the watchdog cannot be used,

and no analogue and H modules can be used on the sockets with base address 240

Connection cables or plugs required

Type of expansion

PCD2.C150 PCD2.C100 PCD3.C100/.C200

PCD2.C2000/

C1000*

Max. expansion

housings or module

holders

Max. plug-in I/O

modules

Max. additional digital

I/Os

127

895

Connecting cable or

PCD2.K1x0

PCD2.K106

PCD3.K1x6

PCD2.K106

PCD3.K1x6

Connector

PCD3.K010

PCD2.K010*

Restrictions

Max. 6 PCD3.C200

*In preparation

Summary of Contents for PCD2.M5 Series





















































































































































































































































Search results

Summary of Contents for PCD2.M5 Series

Reviews:

Related manuals for PCD2.M5 Series

Brands by name

Popular brands

SBC PCD2.M5 Series, Manual

Search results

Summary of Contents for PCD2.M5 Series

Reviews:

Related manuals for PCD2.M5 Series

Brands by name

Popular brands