SBC PCD2.M5 Series Manual Download Page 164

Page: 164 / 244

Hardware Manual for the PCD2.M5 Series│Document 26/856; Version EN 12│2014-07-24

Saia-Burgess Controls AG

Analogue input modules

Input/output (I/O) modules

6-53

Block diagram

INPUT FILTER

E0
E1
E2
E3
E4
E5
E6
E7

ANALOGUE INPUTS

MUX

BUSY (adr. 15)
DATA OUT
10 bits serial

A/D act. (addr. 15)

Clock

Channel address 0.. 7

I/O Bus

DATA

READ

WRITE

ADDR

PCD Bus

+5 V
GND
+24 V

Voltage

Source

10.000 V

7K5

GND

Ref.

Voltage

2.500 V

..W220 only

Watchdog: This module cannot be used on the base address 240, because it would

interact with the watchdog, and would cause a malfunction.

Programming examples for the PCD3.W2x0 can be found in a separate manual and on the

TCS Support site

www.saia-support.com

xx7 and RIOs: the firmware reads in the values according to the configuration (I/O Builder or

network configurator).

Watchdog: This module can interact with the watchdog, if it is used on base address 240. In

this case, the last input with address 255 cannot be used.

For details, please refer to the

"Watchdog" section

, which describes the correct use of the

watchdog in conjunction with PCD3 components.

Summary of Contents for PCD2.M5 Series





















































































































































































































































Search results

Summary of Contents for PCD2.M5 Series

Reviews:

Related manuals for PCD2.M5 Series

Brands by name

Popular brands

SBC PCD2.M5 Series, Manual

Search results

Summary of Contents for PCD2.M5 Series

Reviews:

Related manuals for PCD2.M5 Series

Brands by name

Popular brands