SBC PCD2.M5 Series Manual Download Page 36

Page: 36 / 244

Hardware Manual for the PCD2.M5 Series│Document 26/856; Version EN 12│2014-07-24

Saia-Burgess Controls AG

Installation and addressing of PCD2 I/O modules

PCD2.M5_ Classic CPUs and expansion housings

3-23

3.6

Installation and addressing of PCD2 I/O modules

3.6.1 Insertion of I/O modules

The I/O module is inserted from the side, pushed towards the middle of the unit until it

reaches the end stop, and snapped into the retaining catch.

Retaining clip

Bus connector

No changes (e.g. plugging/unplugging jumpers or I/O modules) should be made with

the power switched on.

3.6.2 Address and terminal designation

8 7 6 5

3 2 1 0

cover of PCD2.M5_

Label field for

I/O modules

LEDs

I/O module

Pin designation

Function label and

relative I/O addresses

All PCD2 systems are provided with a set of matching A4 templates

Removing the cover gives access to terminals, but also exposes components that are

sensitive to electrostatic discharges.

Summary of Contents for PCD2.M5 Series





















































































































































































































































Search results

Summary of Contents for PCD2.M5 Series

Reviews:

Related manuals for PCD2.M5 Series

Brands by name

Popular brands

SBC PCD2.M5 Series, Manual

Search results

Summary of Contents for PCD2.M5 Series

Reviews:

Related manuals for PCD2.M5 Series

Brands by name

Popular brands