SBC PCD2.M5 Series Manual Download Page 154

Page: 154 / 244

Hardware Manual for the PCD2.M5 Series│Document 26/856; Version EN 12│2014-07-24

Saia-Burgess Controls AG

Digital combined input/output modules

Input/output (I/O) modules

6-43

Input/output circuits and terminal designation

E/A5 E/A4 E/A3 E/A2 E1 E0

I/O Bus

PCD Bus

24 VDC

Fuse

The example shows E/A2 and E/A3 used as inputs and

E/A4 and E/A5 used as outputs
The following applies for the inputs:

Switch closed (input positive):

Signal state = “1” = LED on

Switch open:

Signal state = “0” = LED off

Fuse:

It is recommended that each module should be separately protected with a

fast-blow 3.15 A fuse.

Watchdog: This module can be used on all base addresses; there is no interaction with the

watchdog on the CPUs. For details, please refer to the

"Watchdog" section

, which describes

the correct use of the watchdog in conjunction with PCD2 components.

Summary of Contents for PCD2.M5 Series





















































































































































































































































Search results

Summary of Contents for PCD2.M5 Series

Reviews:

Related manuals for PCD2.M5 Series

Brands by name

Popular brands

SBC PCD2.M5 Series, Manual

Search results

Summary of Contents for PCD2.M5 Series

Reviews:

Related manuals for PCD2.M5 Series

Brands by name

Popular brands