SBC PCD2.M5 Series Manual Download Page 225

Page: 225 / 244

Hardware Manual for the PCD2.M5 Series│Document 26/856; Version EN 12│2014-07-24

Saia-Burgess Controls AG

CPUs

Configuration

8-1

Configuration and programming

8.1 CPUs

This section assumes that the user is familiar with the PG5 software. If not, please

refer to Manual 26/733 “PG5”.

8.1.1 Configuring the PCD with PG5

Connecting the PCD to the configuration with PG5:



Start up PG5



Create new project:

● Click on “New…”

● The “New Project” dialogue is displayed

Creating and opening a new project.

The dialogue box is brought up via “File/New Project”. The size of the dialogue

box can be changed by dragging the bottom right corner or by dragging the

frame.

Summary of Contents for PCD2.M5 Series





















































































































































































































































Search results

Summary of Contents for PCD2.M5 Series

Reviews:

Related manuals for PCD2.M5 Series

Brands by name

Popular brands

SBC PCD2.M5 Series, Manual

Search results

Summary of Contents for PCD2.M5 Series

Reviews:

Related manuals for PCD2.M5 Series

Brands by name

Popular brands