SBC PCD2.M5 Series Manual Download Page 192

Page: 192 / 244

Hardware Manual for the PCD2.M5 Series│Document 26/856; Version EN 12│2014-07-24

Saia-Burgess Controls AG

Analogue combined input/output modules

Input/output (I/O) modules

6-82

Function

Power supply

PCD2.W525s must have an external power supply. This power supply is electrically

isolated from both the PCD and the inputs/outputs of the W525. The design also

allows the use of the same power supply for the PCD and the W525 without losing

the galvanic separation. The diagram below shows the various areas of separation:

Timing

●

Inputs

○

Internally, the W525 captures a new value for each input channel every

2 ms

○

This value can be read by the PCD at any time.

○

Depending on the speed of the PCD, the transmission time for each

individual value scaled to 16 bit (for a single input channel) is normally

100 μs.

●

Outputs

○

Internally, the W525 outputs the last output value received from the

PCD with a maximum delay of 2 ms.

○

Depending on the speed of the PCD, the transmission time for each

individual output value scaled to 16 bit is normally 100 μs.

Summary of Contents for PCD2.M5 Series





















































































































































































































































Search results

Summary of Contents for PCD2.M5 Series

Reviews:

Related manuals for PCD2.M5 Series

Brands by name

Popular brands

SBC PCD2.M5 Series, Manual

Search results

Summary of Contents for PCD2.M5 Series

Reviews:

Related manuals for PCD2.M5 Series

Brands by name

Popular brands