SBC PCD2.M5 Series Manual Download Page 70

Page: 70 / 244

Hardware Manual for the PCD2.M5 Series│Document 26/856; Version EN 12│2014-07-24

Saia-Burgess Controls AG

E-display with PCD7.D3100E nano-browser

PCD2.M5_ Classic CPUs and expansion housings

3-57

Display

Joystick

Remove the transparent protec-

tive film from the display

Cleaning advice

Do not use abrasive cleaners and/or cleaning implements that could damage or

scratch the surface of the display. To clean any residues off the surface of the display,

we advise the following procedure:

●

Apply kerosene or ethyl alcohol with a clean soft cloth

●

Then clean with fresh water and rub with a clean soft cloth

Finally, replace the cover of the PCD2.M5_ housing (see section 3.5.3).

3.19.3 Function and use of Joystick

Joystick to navigate within the menu

Pressing the up, down, left and right keys allows:

●

movement and selection of different menu options

●

modification of numeric values

Pressing on the centre generates an ENTER command

Moving between different menu options

Example:

Pressing twice to the left moves from "PCD sys" to "Config".

Summary of Contents for PCD2.M5 Series





















































































































































































































































Search results

Summary of Contents for PCD2.M5 Series

Reviews:

Related manuals for PCD2.M5 Series

Brands by name

Popular brands

SBC PCD2.M5 Series, Manual

Search results

Summary of Contents for PCD2.M5 Series

Reviews:

Related manuals for PCD2.M5 Series

Brands by name

Popular brands